9Display iconsA.B.C.D.E.F.G.H.I.J.Battery capacity indicatorPM displayTime indicatorRDS iconSignal barCT iconAlarm 2 indicatorAlarm 1 indicatorFrequen
10Using the radio for the first timeA. AC operation1. Place your radio on a flat surface.2. Insert the adaptor plug into the AC socket located on the
11Operating your radio – Search tuning AM/FM1. Press the Standby button to switch on your radio.2. Press the Band button as needed until the AM or FM
12Manual tuning – AM/FM1. Press the Standby button to switch on your radio.2. Press and release the Band button to select AM or FM radio mode.3. Rotat
13Setting up the tuning step increment1. Make sure your radio is in power off mode.2. Press and hold the Tuning control knob until the setting of time
14Display modes – FMYour radio has a range of display options for FM radio mode.1. Repeatedly press and release the RDS button to view the RDS info
15Presetting stations in AM/FM modesThere are 5 preset stations each for AM and FM radio. They are used inthe same way for each waveband.1. Press the
16Clock and AlarmsSetting the time formatThe clock display used in stand-by mode and on the playing modescreens can be set to 12 or 24 hour format. Th
17Setting the clock time manually1. Press the Standby button to switch on your radio.2. Press and hold the CT button until the radio beeps once to ent
18Setting the clock time using RDS CT1. Tuning to a station transmitting RDS data, and press and release the CT button. The LCD display will show
1Table of ContentsImportant Safety Instructions ... 2-3Introduction ...
19Setting the alarm clockYour K-200 radio has two alarms which can each be set to wake you toAM/FM radio, buzzer alarm or voice messages. The alarms m
204. Rotate the Tuning control to choose the required alarm type, and then press and release the Tuning control to confirm the setting. The alarm
21When the alarm soundsTo cancel a sounding alarm, press and hold the Alarm 1 or Alarm 2button until the radio beeps once, and the display shows “ALR
22Auto Off TimerYour radio can be set to turn off automatically after a preset timehas elapsed. The Auto Off Timer setting can be adjusted between15,
23Egg Timer function1. Press and release the Egg timer button to enter the egg timer setting. The egg timer setting will start flashing on the disp
24DisplayBrightness controlThe brightness of the display when the unit is in standby mode maybe adjusted. If you use the unit in the bedroom, you may
25Message functionThe message function can record and playback with 2 sets of voicemessage for 30 seconds each.1. Press and hold the Message button to
26Software versionThe software display cannot be altered and is just for your reference.1. Make sure your radio is in power off mode (standby mode).2.
27Auxiliary input socketA 3.5mm stereo Auxiliary Input socket is provided on the rear of yourradio to permit an audio signal to be fed into the unit f
28Circuit FeaturesLoudspeakerOutput PowerHeadphone socketAuxiliary socketAerial System2.5” 8 ohm full range3 Watt / 1.5 Watt (batteries)3.5mm dia3.5m
2Important Safety Instructions1. Read and understand all safety and operating instructions before the radio is operated.2. Retain instruction: The
314. Do not attempt to service the radio yourself. Removing the cover may expose you to dangerous voltage, and will void the warranty. Refer
4IntroductionThe Sangean K-200 AM/FM RDS Digital Tuning Radio provides thefollowing range of features in a stream-lined portable size:Radio for AM and
51.2.3.4.5.6.Backlight buttonRDS buttonStandby / Auto offAlarm 2 buttonBand buttonStation presetsEgg Timer buttonMessage 2 buttonMessage 1 buttonCT (a
612.13.Built-in MicrophoneLCD displayTuning control knobVolume control knob14.15.Controls and connectionsGB
716.17.18.Battery compartmentHeadphone socketAC in socketAux in socketFM Antenna jack19.20.Controls and connections
8Buzzer level control21.Controls and connectionsGB
Kommentare zu diesen Handbüchern