Sangean DDR-22 Spezifikationen Seite 1

GBVevision 1DDR-31BT

9Finding new radio stations – DABAs time passes new stations may become available. To nd new sta-tions proceed as follows:-1. With the radio s

10GBManual Tuning – DABManual tuning allows you to tune your clock radio to a particular DAB frequency. Any new stations found will be added to the st

11Dynamic Range Control (DRC) - DABThe DRC facility can make quieter sound easier to hear when your ra-dio is used in a noisy environment.There are th

12GBOperating your radio – FM auto-tune1. Fully extend the aerial located on the rear of your clock radio. Place the antenna so that it is an stra

13Display modes – FMIn FM mode the bottom line of the display can be set to any of the fol-lowing display options:-1. Press and release the Info butto

14GBPresetting stations - DAB and FMThere are 5 memory presets on the panel for each of the 2 wavebands. However, There are 10 memory presets on the r

15Scan sensitivity settingYour radio will normally scan for FM broadcasts which are strong enough to give good reception. However, you may wish

16GBStereo / Mono setting – FMYour clock radio will play stereo broadcasts in stereo (via headphones) so long as the received signal is of adequate st

17Listening to Bluetooth musicYou need to pair your Bluetooth device with your radio before you can auto-link to play/ stream Bluetooth music through

18GBSetting the time and the date manuallyThe unit will automatically set its clock when tuned to a DAB radio station or to an FM station which is bro

1ContentsControls ... 2-4Mains operation ...

1911. The hour digits on the display will ash. Press the Tuning Up or Down buttons to change the hour digits as needed. 12. Press and release th

20GB20. Press and release the Select button to confirm the year and to complete the clock and date setting. The Time/Date setting is stored

2125. Press the Tuning Up or Down buttons to highlight the option of “Set date format”. 26. Press and release the Select button to enter the “Se

22GBSetting the alarm timesYour clock radio has two alarms which can be set to wake you either radio or buzzer alarm. Each alarm can be set to sou

239. Press and release the Select button to conrm your selection. The alarm duration setting is stored in the radio. 10. The source digits on the

24GB17. The alarm day digits on the display will ash. Press the Tuning Up or Down buttons until the desired the alarm day is set. There are four

2522. Press and release the Select button to conrm the alarm setup setting. The alarm setup setting is stored in the radio. 23. The display will

26GBStop the alarmWhen alarm is active, press the On / StandBy button to stop the alarm (radio and buzzer).Note: When alarm is active, press any b

27Sleep timerYour clock radio can be set to turn off after a preset time has elapsed. The sleep timer can be adjusted between 15 and 90 minutes

28GBEQ functionThe sound on your sound system can be adjusted to suit your personal taste for the material that you are listening to. The unit has six

2GBControls (front) 9. Volume knob10. On / StandBy button11. Tuning control / Select knob12. Preset buttons Preset 2 / Backward Preset 3 /

29Treble control1. Press the EQ button to cycle through the modes until “Treble” appears on the display. The current treble setting will be shown o

30GBMute functionPress the Mute button on the remote control of your radio, it will mute the output from the loudspeaker.1. Press the Mute button to m

31Factory resetIf your clock radio fails to operate correctly or some digits on the display are missing or incomplete, carry out the following procedu

32GBSoftware versionThe software display cannot be altered and is just for your reference. Ensure your radio is switched on and in DAB or FM mode.1

33USB socket for software upgradeSoftware updates for your clock radio may be availabe in the future. As software updates become available software an

34GBLine Out socket1. A 3.5mm stereo Line Out socket is provided on the rear of your sound system to permit the audio signal to be fed to an extern

35SpecicationsPower RequirementsMains: AC 100~240 volts, 50 Hz-60 Hz DC 12V 1A only (switching adaptor)Frequency CoverageFM 87.5 - 108MHzDAB 174.928

3Controls (rear) 13. Telescopic aerial for DAB+ / FM14. USB socket for software upgrade15. DC power in socket16. Headphone socket17. Line Out socket1

4GBControls (remote control)A. B.C.D.E.F.G.H.I.J.K.L.M.N.O.Note: For the sake of clarity, the instructions for the use of the controls throug

5Mains operation1. Place your clock radio on a at surface.2. Plug the mains lead into the Socket located on the rear of your clock radio ensuring

6GBOperating your radio - DAB1. Fully extend the telescopic aerial. Fully extend the telescopic aerial located on the rear of your clock radio. Pla

7Selecting a station - DAB1. The top line of the display shows the name of the station currently selected. 2. Press the Tuning Up or Down buttons

8GBDisplay modes – DABYour clock radio has a range of display modes:-1. Press and release the Info button to cycle through the various modes. a. Sc